Notice: You may have to wait several minutes before the local storage becomes online. Test your sync module by going into the local storage.Standby for the time being and after that, reconnect the cable.Locate the power unit going into your Blink sync module.
#Blink not saving to usb how to
Here’s how to power cycle the Blink sync module in easy steps: If the sync module isn’t communicating with the flash drive correctly, the local storage will not work within your Blink application. Solution #2 Power Cycle The Sync Moduleīefore going any further, it’s recommended to power cycle the sync module to get any startup problems out of the way. Note: Make sure to connect the flash drive properly into the sync module’s port for the local storage to start working again. Then you should check within the Blink app if the local storage is working. Give your system a couple of minutes with the flash drive disconnect and once the time has elapsed, reconnect the flash drive. If that happens, there’s a great way to make your Blink sync module re-identify the flash drive by reconnecting the unit from the USB port.įor this solution, all you have to do is go over to your Blink sync module and disconnect the flash drive. One of the reasons that your local storage has suddenly stopped working is due to the fact that the flash drive isn’t recognized by the sync module.
The only possible problem with the storage could be local and we’re about to find out! Tip: Recording already stored on the flash drive can be viewed on a computer! Solution #1 Re-Identify The Flash Drive
If you don’t have a subscription at Blink, the footage will still be stored automatically onto the flash drive. Let’s start by mentioning that the local storage does not require an active subscription. Since the local storage requires an active sync module and a USB flash drive to store the recordings, a lot of issues can occur with either of these devices. How To Fix When Blink Local Storage Stopped Working? The problem could also be in the sync module itself or simply because the Blink application is not communicating with it. The Blink local storage will not work whenever the USB flash drive is not being recognized by the sync module. Yay.Whenever the Blink local storage not working, there could be several different failures that you would need to inspect.Īs you may know, whenever you don’t have an active subscription the recordings are automatically stored in the USB drive also known as “ Local Storage”.Īny failures in regard to that flash drive will prevent the local storage from working so let’s learn more! I'm already not a huge fan of the Blink system but was finally feeling okay with it and then this happened. Hopefully I won't have to deal with this often. After this, my cameras started recording to the USB again. I then had to connect it to the wifi again so I did that via the Blink app. I never removed the module from the Blink app, the app just indicated the module was offline. I left the USB stick in the module during this entire process. Ultimately what worked for me: I held down the reset button on the Sync Module 2 device until it reset. Just mentioning that since it sounds like support likes to blame the wifi a lot.
#Blink not saving to usb full
In case anyone was wondering, all my cameras have full wifi strength to the router and sync module. I restarted my router also which didn't have any effect. I tried a few basic things (unplug the Sync Module 2 and plug it back in, remove a camera from the system and add it back) which didn't fix anything.
I had this problem recently, all my cameras stopped recording to USB just a few days ago. We have our clients using a Samsung Fit Plus, as they tested better than 100MB/s write speeds in a USB 2.0 port. Although the Sync Module 2 only uses a USB 2.0 connection, we have found that a USB 3.0 drive with fast write speeds is less problematic. And so far all of these drives have had less than stellar write speeds when tested. We have had Sync Module 2s fail to write to a flash drive that was working properly with it earlier. In some cases, this has taken a few days.Īt that point, format the drive to ExFAT and return to service.īlink gave us this procedure after we called them out and escalated the problem awhile back. Afterwards, permanently remove the flash drive until the app requests a subscription or USB storage. What has fixed most of these is a complete reset of the Sync Module without the USB in place. We believe it's caused by a firmware update, but have yet to nail this theory down. We're seeing this issue with more and more of our clients Sync Module 2s. Oh, their customer service will find a number of BS issues from their flip guides.
0 kommentar(er)
